Car Not Starting After Oil Change, Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis), KevweAuto

Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis)

Spread the love

Routine maintenance like an oil change is meant to enhance your car’s operation, not hinder it. But sometimes complicated engines refuse to restart after a fresh oil filter and fill-up. There are a few potential mistakes both DIY and professional mechanics can make that lead to no-start conditions post oil change. Identifying and quickly remedying the cause will get you back on the road.

Common Causes for No Start After Oil Change

Here are some of the most likely reasons an engine won’t start after what should be basic maintenance:

1. Oil Drain Plug Not Reinstalled Properly

  • Allowing oil leak leading to pump pickup starvation

2. Faulty or Loose Oil Filter Installation

  • Permitting air intake or oil leaks

3. Disconnected Sensor or Wiring

  • If removed for access, connector not re-attached properly

4. Oil Overfill

Car Not Starting After Oil Change, Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis), KevweAuto
  • Engine hydrolocks with excess oil in cylinders

5. Damaged Seals or Gaskets

  • From mishandling of components during service
READ ALSO  How Thick Is A Car Tire? (Explained)

6. Sheared Timing Belt/Chain

Car Not Starting After Oil Change, Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis), KevweAuto
  • If tensioner loosened improperly during service

Thorough inspection and diagnosis identifies the specific cause to fix.

Step-By-Step No Start Diagnosis

Follow this methodical process to pinpoint the reason for failure to restart after an oil change:

1. Check Emergency Shut-Off Devices

  • Ensure oil sensor safety switch not erroneously triggered

2. Look for Leaks Near Drain Plug

  • Tighten plug if loose
  • Replace crusher washer if missing or damaged

3. Inspect Filter Seating and Seals

  • Reset filter if loose
  • Ensure gasket fully seated
  • Replace stripped filter adapter if needed

4. Reconnect Loose Sensors and Wiring

  • Especially oil pressure sending unit or level sensor wires
  • Reset trigger thresholds if needed

5. Adjust Oil Level To Proper Range

  • Drain excess if overfilled
  • Top up carefully if under filled

6. Diagnose Timing System Damage

  • Look for loose tensioners or slipped timing chains
  • Check cam/crank correlation for damage

Proper oil change procedures prevent introducing problems. Reversing any errors gets everything lubricating smoothly again.

Best Practices for Oil Changes to Prevent Issues

Car Not Starting After Oil Change, Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis), KevweAuto

Follow these tips for fail-safe oil changes:

  • Use torque wrench on drain plug to prevent under or over tightening
  • Examine old crush washer and replace if damaged
  • Check filter gasket condition and lubricate for easier installation
  • Disconnect sensors carefully and avoid wire damage
  • After filling, idle engine to build oil pressure before revving
  • Align timing marks meticulously if timing components disturbed
  • Road test to verify normal operation before releasing vehicle

Taking the extra time to work carefully prevents most oil change mishaps.

READ ALSO  How To Check Tire Pressure On Volkswagen Jetta (5 Steps To Maintain Proper Jetta Tire Pressures)

Warning Signs of Problems After Oil Change

Watch for these red flags if engine issues arise post oil change:

  • Oil puddles under engine indicating leaks
  • Oil pressure warning light illuminated on dash
  • Unusual engine noises like tapping or rattling
  • Misfires, surging idle, or loss of power
  • Check engine light or timing related fault codes

If any of these arise right after service, promptly investigate for mistakes made. Catching them early prevents further damage.

Getting Back on the Road Again

Car Not Starting After Oil Change, Car Not Starting After Oil Change (6 Step-By-Step No Start Diagnosis), KevweAuto

Assuming no major engine damage was done, fixing oil change errors is usually straightforward:

  • Properly reinstall any components removed like drain plug and filter
  • Ensure sensors reconnected and operating properly
  • Adjust oil level to recommended range
  • Replace damaged seals, gaskets, or o-rings
  • Reset timing components disturbed during service
  • Clear any erroneous fault codes or warning lights

With oil flowing properly again, your engine should be ready to restart and get you back on the road. Learn from any mistakes to prevent repetition.

Conclusion

What should be a quick facilitating maintenance task can go awry and lead to engine no-start conditions if oil change best practices aren’t followed. Paying attention to details like leak-free drain plugs, undamaged sensor connections, and proper fill levels reduces chances of problems. If issues do occur, methodically diagnose the cause then reverse the error. With oil flowing smoothly, your engine will regain its smooth running nature. Don’t let an oil change take away your mobility.

Ejenakevwe Samuel

I'm Ejenakevwe Samuel, and my blog is all about sharing the love for cars. Through my blog, I pour my heart into educating fellow car enthusiasts in everything they need to know about their beloved rides. Whether it's driving tips, maintenance tricks, or the latest trends, I aim to empower others to make informed decisions and take care of their vehicles like a pro.

Leave a Reply